Is it possible to make use of a mouse in any way outside the X Window?
If you are using the default console driver, syscons, you can use a mouse pointer in text consoles to cut & paste text. Run the mouse daemon, moused, and turn on the mouse pointer in the virtual console: moused -p /dev/xxxx -t yyyy vidcontrol -m on Where xxxx is the mouse device name and yyyy is a protocol type for the mouse. See the moused man page for supported protocol types. You may wish to run the mouse daemon automatically when the system starts. In version 2.2.1, set the following variables in /etc/sysconfig. mousedtype=”yyyy” mousedport=”xxxx” mousedflags=”” In versions 2.2.2 or later, set the following variables in /etc/rc.conf. moused_type=”yyyy” moused_port=”xxxx” moused_flags=”” In addition, if you would like to be able to use the mouse daemon on all virtual terminals instead of just console at boot-time, add the following to /etc/rc.conf. allscreens_flags=”-m on” Staring from FreeBSD 2.2.6, the mouse daemon is capable of determining the correct protocol type automatically
If you are using the default console driver, syscons, you can use a mouse pointer in text consoles to cut & paste text. Run the mouse daemon, moused, and turn on the mouse pointer in the virtual console: moused -p /dev/xxxx -t yyyy vidcontrol -m on Where xxxx is the mouse device name and yyyy is a protocol type for the mouse. See the moused man page for supported protocol types. You may wish to run the mouse daemon automatically when the system starts. In version 2.2.1, set the following variables in /etc/sysconfig. mousedtype=”yyyy” mousedport=”xxxx” mousedflags=”” In versions 2.2.2 or later, set the following variables in /etc/rc.conf. moused_type=”yyyy” moused_port=”xxxx” moused_flags=”” Staring from FreeBSD 2.2.6, the mouse daemon is capable of determining the correct protocol type automatically unless the mouse is a relatively old serial mouse model. Specify “auto” as the protocol to invoke automatic detection. When the mouse daemon is running, access to the mouse needs to be co
If you are using the default console driver, syscons, you can use a mouse pointer in text consoles to cut & paste text. Run the mouse daemon, moused, and turn on the mouse pointer in the virtual console: moused -p /dev/xxxx -t yyyy vidcontrol -m on Where xxxx is the mouse device name and yyyy is a protocol type for the mouse. See the moused(8) man page for supported protocol types. You may wish to run the mouse daemon automatically when the system starts. In version 2.2.1, set the following variables in /etc/sysconfig. mousedtype=”yyyy” mousedport=”xxxx” mousedflags=”” In versions 2.2.2 to 3.0, set the following variables in /etc/rc.conf. moused_type=”yyyy” moused_port=”xxxx” moused_flags=”” In 3.1 and later, assuming you have a PS/2 mouse, all you need to is add “moused_enable=”YES” to /etc/rc.conf. In addition, if you would like to be able to use the mouse daemon on all virtual terminals instead of just console at boot-time, add the following to /etc/rc.conf. allscreens_flags=”-m on
If you are using the default console driver, syscons, you can use a mouse pointer in text consoles to cut & paste text. Run the mouse daemon, moused, and turn on the mouse pointer in the virtual console: moused -p /dev/xxxx -t yyyy vidcontrol -m on Where xxxx is the mouse device name and yyyy is a protocol type for the mouse. See the moused(8) man page for supported protocol types. You may wish to run the mouse daemon automatically when the system starts. In version 2.2.1, set the following variables in /etc/sysconfig. mousedtype=”yyyy” mousedport=”xxxx” mousedflags=”” In versions 2.2.2 or later, set the following variables in /etc/rc.conf. moused_type=”yyyy” moused_port=”xxxx” moused_flags=”” In addition, if you would like to be able to use the mouse daemon on all virtual terminals instead of just console at boot-time, add the following to /etc/rc.conf. allscreens_flags=”-m on” Staring from FreeBSD 2.2.6, the mouse daemon is capable of determining the correct protocol type automatical
